Reger Laser

Author name: Brady Collette

Laser cutting machine in a spacious factory
Buying & Ownership

What Do You Do With the Old Machine When You Upgrade?

Replacing a laser cutting machine goes wrong most often at the end, not the beginning. Shops spend months evaluating the new machine and about ten minutes thinking about the old one, and then the new equipment arrives while the old machine is still bolted to the floor in the only spot it fits. The decision you need to make early is simple to state and easy to postpone: does the old machine stay as backup capacity, leave as a remarketed asset, or get scrapped? Each answer implies a different timeline, a different amount of work, and a different set of people who need to be scheduled. Make the call before the new machine has a ship date, because after that the choice makes itself, usually badly and usually in the most expensive direction. Table of Contents Replacing a Laser Cutting Machine Starts With One Decision Keeping It as Backup Capacity Remarketing It Scrapping It What Has to Happen Physically Frequently Asked Questions Replacing a Laser Cutting Machine Starts With One Decision The forcing constraint is almost always floor space. Most shops do not have room to stage a new laser next to the old one, which means the old machine has to be out before the new one comes in, or the two have to overlap somewhere temporarily. Both of those require planning that starts weeks ahead of delivery. There is also a production gap to manage. Whatever you were cutting on the old machine still has due dates during the changeover. Deciding the old machine’s fate early is what lets you sequence the two, and it is why this conversation belongs alongside the purchase rather than after it. Our guide to buying a fiber laser cutting machine covers the acquisition side of the same project. Get the people who actually have to live with the answer into that decision early. Your operators know whether the old machine still earns its keep on thin work. Maintenance knows what it has been costing them in attention. Whoever handles scheduling knows what happens to your lead times if you lose that capacity for three weeks. A changeover planned entirely in an office tends to discover all three of those constraints in the same week the truck arrives. Keeping It as Backup Capacity The case for keeping the old machine is real and underrated. A second machine, even a slower one, means a breakdown on the new machine is a slowdown rather than a stop. It also gives you somewhere to put thin-material work, prototypes, or the job that always ties up the good machine. The case against is that a machine you keep is a machine you maintain. Consumables, a service relationship, a chiller running, spare parts on the shelf, and an operator who remembers how to run it. A backup machine that sits for a year without being started is not backup capacity, it is furniture, and it will need work before it cuts anything. If you keep it, run it regularly and keep it on a preventive maintenance schedule, even a light one. Remarketing It A working machine with documented maintenance history and a clean service record is worth considerably more to the next owner than an identical machine with no records. That is the one lever you control, and it is worth pulling before you list anything. Pull together the service records, the manuals, the original documentation, the remaining spare parts and consumables, and any tooling or fixtures that belong with it. Have someone verify the machine cuts to spec and save the sample parts. A buyer evaluating two similar machines will take the one that comes with evidence, and the same evidence shortens the negotiation. It also matters that the machine is presented honestly, because a known and disclosed fault is a normal part of a used machine transaction and a hidden one is a dispute. Our used Tanaka machines page shows the kind of information a serious buyer expects to see. Scrapping It Sometimes a machine has reached the end. A dead source on an obsolete platform, a control generation nobody supports, or a frame that has been through a flood can all make the economics obvious. Scrapping is a legitimate answer and it is faster than the alternatives. Two things to handle properly on the way out. First, strip the parts worth keeping before it goes, particularly if you are running a similar machine elsewhere in the shop. Second, the chiller contains refrigerant, and refrigerant recovery is regulated rather than optional. The EPA’s stationary refrigeration and air conditioning requirements cover who is allowed to do that work and how, and a scrap dealer is not automatically that person. What Has to Happen Physically Whichever path you pick, the machine has to be shut down properly and moved. Neither of those is a general maintenance task. Decommissioning and Rigging Power has to be disconnected and locked out, gas lines depressurized and disconnected, coolant drained and disposed of properly, and the fume extraction separated. That is lockout work, and OSHA’s control of hazardous energy guidance describes the procedure that should be in place before anyone touches a disconnect. Then comes the part that surprises people: the machine has to leave the building the way it came in, and the building has often changed since then. Doors get filled in, racking goes up, a wall gets added, and the clear path that existed at installation is gone. Measure the route before you commit to a date. A laser is also not a machine you push around on rollers, since alignment, frame stress, and the way it is anchored all matter. We cover that work in laser machine relocation and in moving a laser cutting machine. Frequently Asked Questions How far ahead should this be planned? Start when the new machine is ordered, not when it ships. Rigging crews, electricians, and service technicians all need scheduling, and the exit route survey should happen while there is still time to

Industrial cooling system with pipes and grids outdoors
Orion Chillers

How Do You Size a Chiller for a Laser?

Sizing a laser chiller starts with the machine builder’s cooling requirement and then accounts for everything that requirement assumes. The source has a specified heat load, but the chiller also has to handle the cutting head, sometimes the drives, and it has to do it in your building rather than in a lab. Ambient temperature around the unit, how long the machine runs without a break, how the plumbing is routed, and how clean the air is all change what capacity actually delivers on your floor. A chiller that matches the spec on paper and sits in a hot corner behind a rack of material will fall behind on a long production run, and the machine will tell you about it through drifting cut quality long before an alarm appears. Get the environment into the calculation and the unit will hold. Table of Contents Sizing a Laser Chiller Starts With the Builder’s Requirement What Changes the Number on Your Floor Duty Cycle Is the One People Miss Plumbing, Placement, and Airflow Signs the Chiller Is Undersized Frequently Asked Questions Sizing a Laser Chiller Starts With the Builder’s Requirement The machine manufacturer specifies a cooling capacity, a flow rate, a pressure range, and a temperature band, and those are not suggestions. The temperature band in particular exists because the source and optics are designed around it. Running warm degrades performance and shortens component life. Running too cold risks condensation inside the machine, which is its own expensive problem. Cooling capacity is commonly quoted at specific conditions, so a rating is only meaningful when you know the conditions behind it. Industry ratings for this equipment are standardized by bodies such as AHRI, which is worth knowing when you are comparing two units whose datasheets do not look alike. A capacity figure without stated conditions tells you very little. Flow and pressure deserve the same attention as capacity, and they get skipped constantly because capacity is the number on the front of the brochure. The source needs a specific volume of coolant moving through it at a specific pressure, and a unit with plenty of cooling capacity but the wrong pump curve for your plumbing will not deliver it. Ask for the pump performance data, not just the tonnage, and check it against the actual run length and hose size you intend to install. This is the single most common reason a correctly sized chiller underperforms after installation. What Changes the Number on Your Floor An air-cooled chiller rejects heat into the room it sits in. As the air around the condenser gets warmer, capacity drops, and it drops exactly when you need it most, which is during a long hot summer run in a building with a lot of machines in it. Four things in your building change the working number: the ambient temperature in the actual corner where the unit lives, how much clearance it has for airflow, how clean the air is, and elevation. Shops with heavy dust and spatter foul condenser coils fast, and a fouled coil is a capacity reduction you cannot see. Consider where people work near that equipment too, since a chiller dumps its heat into the same space as your operators, which OSHA’s guidance on working in indoor heat environments is a reminder to think about. Duty Cycle Is the One People Miss Two shops can run the same machine and need different cooling. A job shop cutting short nests with setup time between them gives the chiller regular recovery. A production shop running long nests back to back, two shifts, on thick plate, never does. Sizing to the average load is how you end up with a unit that is fine for three hours and behind by hour five. Size to the sustained worst case you actually run, not to a typical day. The symptom of getting this wrong is specific and recognizable: everything is fine in the morning and cut quality drifts in the afternoon, then recovers overnight. If that pattern sounds familiar, the cooling system is the first place to look, and why precise chiller temperature control matters covers what that drift does downstream. Plumbing, Placement, and Airflow Capacity is what the unit can do. Delivery is what reaches the machine, and the plumbing between them decides the difference. Long runs, undersized hose, unnecessary elbows, and partially closed valves all cost flow, and flow is part of the specification, not an afterthought. A chiller at the correct temperature with insufficient flow still fails to cool properly. Placement deserves more thought than it usually gets. Give the unit the clearance the manufacturer asks for on every side, keep it out of the path of dust and spatter, and do not tuck it into an alcove where it recirculates its own hot exhaust. If you are laying out a new install, handle this at the same time as everything else in fiber laser installation requirements rather than finding a spot for the chiller after the machine is set. Signs the Chiller Is Undersized Coolant temperature climbs above setpoint during long runs and recovers at idle. The compressor runs nearly continuously instead of cycling. Cut quality degrades through a shift with no other change. Temperature alarms appear only in warm weather or only on second shift. The machine throttles or derates on its own. Before concluding it is undersized, rule out the maintenance items that mimic it, because a neglected chiller behaves exactly like a small one. Fouled coils, low or degraded coolant, a plugged filter, or a failing pump all reduce effective capacity. Work through why a laser chiller overheats and laser chiller coolant first. Replacing a healthy unit with a bigger one because the old one had dirty coils is an expensive way to clean a coil. Frequently Asked Questions Should I oversize on purpose? Some margin is sensible, particularly for summer ambient and for a machine you may upgrade later. Large oversizing has its own drawbacks, including short cycling and poorer

Technician using a machine control panel
Training & Safety

What Should a New Laser Operator Learn First?

A new laser operator should learn the machine before they learn the part. The instinct in a busy shop is to get someone producing on day two, so training starts with loading a program and pressing cycle start, and three months later you have somebody who can run the jobs they have seen and has no idea what to do when the cut goes bad. The better order is safety first, then how the machine behaves and what it is telling you, then consumables and cut quality, then material handling and setup, and only then programming and nesting. It is slower for the first two weeks and considerably faster after that, because an operator who understands what a good cut looks like and why it went wrong stops needing somebody else to walk over and look at it. Table of Contents What a New Laser Operator Does in Week One The Order That Actually Works What Takes Longer Than People Expect How to Tell If Training Is Working Frequently Asked Questions What a New Laser Operator Does in Week One A laser cutting system is a high-power beam, a fast-moving gantry, compressed gas, high voltage, and a fume stream, all in one enclosure. A new operator needs to understand what each of those can do before they need to understand feeds and speeds. Start with the specific hazards of the machine in front of them rather than a generic video. Where the interlocks are and what happens when they open. Where the emergency stops are and what each one actually stops. Where the gas shutoff is. What the fume extraction does and why it runs. OSHA’s overview of laser hazards is a reasonable framework for the written side of that, and our own safety tips for operating laser cutting machines covers the shop-floor version. The Order That Actually Works 1. Safe Startup, Shutdown, and Stop Before anything is cut, the operator should be able to bring the machine up from cold, put it to sleep correctly, and stop it safely three different ways. Shutdown gets skipped in training constantly, and it is where damage happens: a chiller left off, gas left pressurized, a head left parked against something. Teach the end of the shift as carefully as the start. 2. Reading the Machine, Not Just the Screen Good operators run on their senses as much as the control. The cut has a sound, and a bad cut has a different one. Sparks behave a certain way when the gas and focus are right. The chiller cycles on a rhythm you can learn. None of that is on the display, and it is the earliest warning you will ever get. Pair that with the daily routine from day one, so checks are a habit rather than a form somebody signs at the end of the week. Our daily laser cutter checklist is a workable starting point to adapt to your machine. 3. Consumables and What a Good Cut Looks Like An operator who cannot recognize a worn nozzle or a contaminated protective window will keep running until the parts are scrap. Teach them to inspect and change consumables early, and teach them to judge an edge. Keep physical sample parts at the machine: a good edge, a dross-heavy edge, a burned edge, a rough one. A reference you can hold beats a description every time, and laser cut edge quality covers what each condition points to. 4. Material Handling and Setup Sheet that is not flat, not clean, or not what the program expects causes problems that look like machine faults. Loading, squaring, checking material condition, and confirming thickness are all part of the job and all get taught last when they should be taught fourth. 5. Programs, Nesting, and Optimization Now they can learn to run programs, adjust parameters within limits you set, and understand nesting. By this point they know what the machine should sound like, what the edge should look like, and what to check when it does not, so a parameter change is an informed decision instead of an experiment. What Takes Longer Than People Expect Judgment is the slow part. Recognizing that the cut is drifting before it produces scrap, knowing when to stop and change a consumable versus finishing a nest, knowing when a problem is theirs and when it needs a technician. That is pattern recognition built from seeing enough situations, and it does not compress into a class. Structured programs help. Formal apprenticeship frameworks exist for manufacturing roles and are worth a look if you are building a pipeline rather than filling one seat, and Apprenticeship.gov is the place to start reading. For getting a specific person productive on a specific machine, our laser operator training is built around your equipment rather than a generic curriculum. How to Tell If Training Is Working Output is a lagging and misleading measure, because a new operator running easy repeat work looks excellent right up until something changes. Better signals are whether they catch problems before scrap, whether their daily checks are actually being done, whether they can explain why a cut went wrong rather than just that it did, and whether they ask for help at the right moment instead of too late. One more that matters in a multi-shift shop: does the machine come back the same way it was left? An operator who shuts down properly and leaves the area clean is telling you their training took. It is also worth deciding up front who owns the training. In most shops it defaults to whoever is least busy that week, which produces an operator who learned five different habits from five different people. Name one person as the trainer, give them the outline above, and have them sign off on each step. That costs an hour of planning and it is the difference between a program and a series of favors. When the trainer is also your best operator, protect their time

Numbered parts bins on warehouse shelving
Parts & Consumables

How Do You Find the Right Part Number for a Laser Machine?

Getting laser machine part numbers right starts with the machine, not the part. Pull the serial number and the exact model designation off the data plate first, because the same model name can cover several configurations built years apart with different components underneath. A cutting head, a drive, or a control board that fits one build of a machine will not always fit the next one, and the difference is rarely visible in a photo. Once you have the serial number, the model, and a clear description or picture of what failed, identification is usually quick. Without it, you are guessing, and the wrong part in a box costs more downtime than no part at all, because you spent the shipping time waiting for the wrong thing. This is the single most common reason a parts order goes sideways. Table of Contents Why Laser Machine Part Numbers Are Harder Than They Should Be What to Have Ready Before You Call Consumables Are a Different Problem Where a Parts Picker Helps OEM, Aftermarket, and What Not to Gamble On Frequently Asked Questions Why Laser Machine Part Numbers Are Harder Than They Should Be Machine tools get revised constantly and quietly. A supplier changes, a component gets superseded, a control generation rolls over, and the model badge on the front of the machine stays exactly the same. Ten years later the machine on your floor and the machine in the catalog photo share a name and not much else. Then there is the paperwork problem. Manuals go missing during a move, get filed by whoever ran the machine three owners ago, or cover a different build than the one you own. Machines bought used often arrive with no documentation at all, which is worth knowing before you need a part in a hurry rather than during a breakdown. There is a third complication that only shows up on older equipment. Machines get modified over their lives. A previous owner replaces a drive with whatever was available, a service call swaps a component for a superseded version, or a head gets upgraded. None of that gets recorded anywhere, so the parts list for your serial number is correct for how the machine left the factory and not necessarily for how it sits on your floor today. That is why photographs of the actual failed part matter as much as the serial number, and why we ask for both rather than one or the other. What to Have Ready Before You Call Five things turn a long phone call into a short one. The machine serial number, read off the plate, not from memory. The full model designation including any suffix or series letters. Approximate year of manufacture or year you acquired it. Clear photos of the failed part, including any label, stamp, or casting number on it. What the machine was doing when it failed, and what it does now. The Data Plate Is the Starting Point Find the plate once and photograph it, then keep that photo somewhere the whole shop can reach. Do it today rather than during a breakdown, because the plate is frequently in an awkward spot on the frame, behind a guard, or on the back of the machine facing a wall. The serial number is the key that unlocks the correct parts list for your specific build, and every minute spent crawling around looking for it is downtime. While you are at it, photograph the control cabinet labels and any drive or servo tags. Those carry their own part numbers, and having them on file means an electrical fault does not start with someone opening a panel to read a sticker. If a panel does have to come open, that is lockout territory, and OSHA’s control of hazardous energy guidance describes the procedure that should be in place before anyone does it. Consumables Are a Different Problem Nozzles, protective windows, ceramics, and similar wear items are identified by fit and specification rather than by a machine serial number, which makes them easier to source and easier to get wrong in a subtle way. A nozzle with the right thread and the wrong orifice diameter will install perfectly and cut badly, and it will take somebody half a day to figure out why the machine suddenly got worse. The fix is to record what you actually run rather than reordering from memory. Write the exact specification on the bin. We covered selection in choosing a laser cutting nozzle and in the laser protective window, and what to keep in stock in laser machine spare parts. Where a Parts Picker Helps The reason we built a parts picker is that most of the friction in this process is people describing parts to each other in words. A picker lets you work from the machine down to the component visually, which removes the step where a description gets interpreted two different ways. For Tanaka machines specifically, our Tanaka LMX parts page covers that line directly. If your machine came to you secondhand and you are not certain what you have, send us the data plate photo. Identifying a machine from its plate is routine for us, and it beats ordering twice. OEM, Aftermarket, and What Not to Gamble On Aftermarket parts are a real option in some categories and a bad idea in others. The dividing line worth using is whether the part is in the beam path, in a safety circuit, or in a precision motion assembly. Optics and beam-path components affect both cut quality and safety, and substituting them based on a dimensional match is a gamble with the most expensive parts of the machine downstream. Anything tied to an interlock or a guard is the same conversation, and OSHA’s machine guarding material is a reminder of why those circuits exist. Commodity items such as filters, belts, and fittings are usually fine from a good supplier, as long as the specification actually matches rather than approximately matches.

Industrial fiber laser cutting machine on a shop floor
Maintenance & Service

Why Is My Fiber Laser Losing Cutting Power?

A fiber laser losing power is almost never a dying laser source, and the shops that assume it is end up spending on the most expensive component in the machine to fix something that was in the cutting head. Fiber sources are among the most reliable parts of the system. What changes over time is everything the beam has to travel through on the way to the plate: a protective window that has taken spatter, contaminated optics, a worn nozzle, a focus position that has drifted, assist gas that is not what it used to be, or a chiller that is no longer holding the temperature the source expects. Any one of those looks exactly like lost power at the cut. Working through them in a sensible order takes a shift, not a service contract, and it tells you what you are actually dealing with before anybody quotes you a source. Table of Contents Is the Fiber Laser Losing Power, or Is the Cut? The Cheap Causes, in Order Cooling Is a Common Culprit When the Source Really Is Degrading A Diagnostic Order That Saves Time Frequently Asked Questions Is the Fiber Laser Losing Power, or Is the Cut? Before you chase anything, separate two different complaints. One is that the machine no longer cuts what it used to cut. The other is that measured output at the head has dropped. They feel identical on the floor and they point in different directions. Cut performance depends on power, focus, gas, nozzle condition, standoff, material, and program. Any of those can degrade a cut while the source is putting out exactly what it always did. A power measurement at the head, taken the same way each time, is the only thing that separates a real output problem from a delivery problem. If you have historical readings, compare against them rather than against the nameplate rating. If you do not, start recording them now, because the next time this happens you will want the baseline. One safety note before anyone opens anything. Service work on a laser means following the machine’s lockout procedure and treating the beam path as live until it is proven otherwise. OSHA’s guidance on control of hazardous energy and on laser hazards covers what that should look like in writing. The Cheap Causes, in Order The list below is ordered by how often it turns out to be the answer, not by how interesting it is. Protective Window and Optics This is the first thing to check and the most common answer. The protective window sits directly in the beam path and directly in the line of fire from spatter. Contamination on it absorbs energy instead of passing it, which both reduces what reaches the plate and heats the window itself, accelerating the damage. A window that looks acceptable under shop light can be badly degraded, and marks near the center matter more than marks near the edge. We wrote about inspection and replacement in the laser protective window. Further up the chain, the fiber connector at the head is the other optical suspect. Contamination there does not just reduce output, it can damage the connector under power. That is not a shop-floor cleaning job on most machines, and guessing at it is how a bad afternoon becomes an expensive one. Nozzle, Standoff, and Focus A nozzle with a damaged or out of round orifice disrupts the gas column even when the beam is fine, and the result on the plate reads as insufficient power. Nozzles are consumables and they are cheap relative to the time spent diagnosing around them, so swap in a known good one early rather than late. Our notes on selection are in choosing a laser cutting nozzle. Focus position is the quiet one. A focus that has drifted puts a larger, less intense spot on the material, which behaves exactly like reduced power. Verify focus with whatever method your control provides before you conclude anything about the source. Assist Gas Gas pressure at the nozzle, not at the bottle, is what matters, and a restriction anywhere in the line drops it. Purity matters too, especially on nitrogen work, and a cylinder swap or a bulk delivery is a legitimate suspect if the problem started on a specific day. Keep gas handling within the practices described in OSHA’s compressed gas and equipment material, and see assist gas for laser cutting for how the choice affects the cut. Cooling Is a Common Culprit Laser sources and optics expect to run in a narrow temperature band, and a chiller that has quietly fallen behind changes the machine’s behavior long before it throws an alarm. Fouled condenser coils, low or degraded coolant, a restricted filter, or a plugged heat exchanger all reduce capacity gradually, so the machine gets worse over weeks and nobody connects it to the cooling system. Check the actual temperature the chiller is holding under load, not the setpoint on the display. A unit that holds fine at idle and drifts during a long production run is telling you something specific. We covered the failure patterns in why a laser chiller overheats and the fluid side in laser chiller coolant. If the unit itself is at the end of its life, our Orion industrial water chillers page covers replacements. When the Source Really Is Degrading It does happen, and there is a pattern to it. Real source degradation is gradual, consistent, and shows up as measured output declining over months regardless of what you change downstream. It does not appear overnight, it does not come and go, and it does not get better when you install a fresh protective window. Sudden loss is much more likely to be a fault or a protection circuit doing its job. Intermittent loss is usually thermal, electrical, or a connection. Both of those are worth diagnosing properly before anyone talks about a source, and both are the kind of thing our laser resonator repair service exists to

Fiber laser cutting steel and throwing sparks, the result shops compare when buying a fiber laser cutting machine
Buying & Ownership, Laser Cutting

What Should You Compare Before Buying a Fiber Laser Cutting Machine?

When buying a fiber laser cutting machine, compare machines on the things that decide how they will run in your shop for years, not just the headline numbers on the spec sheet. That means laser power matched to your real thickness range, a bed size that fits your sheet stock, the cutting head and control, the motion system, how the machine handles material, whether it can take automation later, what your site needs to support it, and the service, parts, and training behind it. Two machines with the same wattage can perform very differently on your parts. The most reliable comparison is a cut sample of your own part in your own material, backed by honest answers about support. This guide walks through ten things to compare, in roughly the order they matter, so the machine you pick is the one that fits your work rather than the one with the biggest number on the brochure. Table of Contents Start by Buying a Fiber Laser Cutting Machine for Your Work Power, Bed Size, and Cutting Head Control, Software, and Motion Material Handling and Automation Site Requirements and Safety Service, Parts, and Training Proof: Cut Samples on Your Parts Frequently Asked Questions Start by Buying a Fiber Laser Cutting Machine for Your Work Reger Laser sells Tanaka laser cutting machines and services machines from most major manufacturers, and the shops that end up happiest with a new laser are the ones that started with a clear picture of their work. Before comparing machines, write down the materials you cut, the thickness range, typical sheet sizes, part volumes, the edge quality your customers expect, and what you expect to add over the next few years. If you are still deciding whether laser is the right process at all, our comparison of fiber laser vs plasma cutting is a good place to start. If you are weighing new against used, see our post on choosing a new or used laser cutting machine. Power, Bed Size, and Cutting Head 1. Laser power More power cuts thicker material and cuts thin material faster, but it is only worth paying for if your work uses it. Match power to the thickness range you cut most often, with some room for growth, rather than to the thickest part you cut twice a year. Our fiber laser cutting thickness post explains the difference between the maximum a machine can pierce and what it can cut well in production. Think about the assist gas side of power as well. Cutting thicker material or cutting faster often means more nitrogen or oxygen at higher pressure, so a power choice is also a choice about your gas supply. Ask each seller what gas setup their machine expects for the work on your list, and make sure your supplier can deliver it. 2. Bed size Pick a bed that fits the sheet sizes you buy, and think about whether larger sheets would improve your nesting. A bed that is too small forces you to buy cut-down sheets. One that is far too large takes floor space you may need for something else. 3. Cutting head The head decides a lot about day-to-day running. Compare focus control, how the head protects its optics, how easy the protective window and nozzle are to change, and how well it recovers from a tip-up or collision. Ask how head parts are sourced and how quickly they arrive. Control, Software, and Motion 4. Control and software Operators spend their whole shift at the control, so it matters. Look at how cutting tables are managed, how easy it is to recover from an interrupted program, and whether it works with the nesting software you use or plan to use. 5. Motion system and frame Speed and acceleration numbers look good on paper, but accuracy over years of use depends on the frame, the rails, and the drive system. Ask how the frame is built and how the machine holds alignment over time. The reasons shops rely on Tanaka machines come down largely to this. Material Handling and Automation 6. Table exchange and part removal A shuttle table lets the operator load the next sheet while the machine cuts, which keeps the beam on. Look at how fast tables exchange, how slats are changed, and how scrap and small parts are handled. 7. Room for automation later Even if you are not automating now, ask whether the machine can accept load and unload systems, storage, or part sorting later. Buying a machine that cannot grow with you limits options down the road. Our laser cutting automation page covers what is available. Site Requirements and Safety 8. What your building needs Every machine has requirements for electrical service, floor, assist gas, cooling, and fume extraction. Get them in writing before you buy, and have your electrician confirm the service against the machine’s needs and the National Electrical Code (NFPA 70) your local inspector enforces. Our installation requirements post lists what to check. Look at how each machine contains the beam, too. Fiber lasers cut with infrared light that is invisible and dangerous to eyes and skin, so the enclosure, viewing windows, and interlocks matter. OSHA’s laser hazards overview explains the risks. Service, Parts, and Training 9. Who supports the machine A laser that is down is not making parts. Ask who services the machine in your area, how quickly a technician can be on site, how parts are stocked, and what operator training is included. Also ask for running costs beyond the purchase, including gas, power, consumables, and maintenance. Our fiber laser operating cost post lists what goes into that number. Talk to other shops running the same machine if you can. They will tell you how service has actually worked when something broke, which is worth more than any promise made during a sale. Proof: Cut Samples on Your Parts 10. See it cut your work Brochure cuts are chosen to look good. Send your own part files

Laser cutter operating in a factory, the investment behind the new versus used laser cutting machine decision
Buying & Ownership, Laser Cutting

Should You Buy a New or Used Laser Cutting Machine?

The new vs used laser cutting machine decision comes down to four things: how soon you need the machine running, what technology your work actually requires, how much you can verify about a used machine’s condition and history, and what support comes with each option. A used machine with a documented service history, a healthy source or resonator, and parts still available can be a smart way to add capacity quickly. A new machine makes more sense when your work needs capabilities older machines do not have, when you want automation built in from day one, or when a used option comes with too many unknowns. Neither answer is right for every shop. This guide walks through the questions we ask shops when they come to us weighing both, so you can make the call with the facts in front of you instead of a gut feeling. Table of Contents Start With the Work, Not the Machine Timing and Availability Technology and Capability Condition and History of a Used Machine Support, Parts, and Training Financing and Tax Questions A New vs Used Laser Cutting Machine Checklist Frequently Asked Questions Start With the Work, Not the Machine Reger Laser sells both new Tanaka laser cutting machines and used Tanaka machines, so we do not have a reason to push one over the other. What we push is starting with the work. List the materials you cut, the thickness range, the sheet sizes, the part volumes, and the edge quality your customers expect. Then list what you expect to be cutting in a few years. That list, not the machine brochure, tells you what capabilities you actually need. Our post on fiber laser cutting thickness is a good reference for matching machine capability to the material you cut. Timing and Availability If you need capacity soon because work is already waiting, timing can decide the question on its own. A used machine that is available now, has been inspected, and can be moved and recommissioned quickly may get you cutting well before a new machine could be built, shipped, and installed. On the other hand, a new machine lets you plan the installation, the site, and the training on your schedule, without racing to buy a used machine before someone else does. Technology and Capability Laser cutting technology has changed a lot. Older used machines may be CO2 instead of fiber, may have lower power, older controls, or cutting heads without features newer shops take for granted. That does not make them bad machines. A well-maintained CO2 laser still cuts thick plate beautifully. But it does mean you should check whether a used machine can actually do your work, not just whether it is in good shape. Is it fiber or CO2, and which one suits your material mix? Is the power right for your thickness range? Is the control current enough to be supported, and does it run your nesting software? Is the bed size right for your sheet stock? Can it take the automation you may want later? Condition and History of a Used Machine This is where the new vs used laser cutting machine question gets decided for most shops. A used machine is only as good as what you can verify about it. Ask for service records, run hours, and the history of major repairs. See it run under power, cutting material you actually cut. Have a technician who knows the machine inspect the source or resonator, the motion system, the cutting head, the chiller, and the control. Our used fiber laser buyer’s inspection guide walks through that inspection step by step, and our post on fiber laser source lifespan explains how to think about the source, which is usually the most important component to evaluate on a used fiber machine. Support, Parts, and Training A laser is only as useful as the support behind it. Before buying either way, find out who will service the machine, how quickly parts can be sourced, and who will train your operators. With a used machine, confirm that parts for that specific model and control are still available, because a machine that is down for weeks waiting on an obsolete board is not a bargain at any price. Ask each seller exactly what support and coverage come with the machine, in writing. Plan operator training into the timeline either way, since even experienced operators need time on a machine that is new to them. Financing and Tax Questions How you pay for the machine can matter as much as which one you buy. Many shops finance equipment through a lender or the seller, and the U.S. Small Business Administration’s 504 loan program is built for long-term fixed assets such as major equipment. Tax treatment for new and used equipment also matters, and the rules change. IRS Publication 946 covers how business property is depreciated. Talk to your accountant before you sign, because the right structure depends on your business, not on the machine. A New vs Used Laser Cutting Machine Checklist When you have a new option and a used option in front of you, run both through the same list. Can it cut the materials and thicknesses on your list today and in a few years? When could it realistically be cutting parts in your building? What do you know for certain about its condition, and what is still a guess? Who services it, and how fast can parts arrive? What support and coverage come with it, in writing? Does your site already meet its power, gas, and floor requirements? Our installation requirements post covers the list. What training does your team need to run it well? If the used option has clear answers to every question, it is a real contender. If several answers are still guesses, the new option usually carries less risk. It also helps to write down what happens if each option goes wrong. If a used machine needs an unexpected repair in its first

Steel process pipes in a factory building, the type of plumbing that carries coolant between a laser chiller and the machine
Maintenance & Service, Orion Chillers

What Coolant Should You Use in a Laser Chiller?

The right laser chiller coolant is whatever the laser manufacturer specifies for your machine, and for most fiber and CO2 cutting machines that means distilled or deionized water, sometimes with a specific corrosion inhibitor or biocide the manufacturer approves. It almost never means tap water, and it only means antifreeze when the manual says so and at the concentration the manual gives. The reason is simple. The coolant does not just pass through the chiller. It runs through the laser source, the cutting head, and in some machines the optics, and the passages in those parts are small, expensive, and hard to clean. Minerals, corrosion, and biological growth that a garden hose would never notice can scale a heat exchanger, clog a head, or trip a conductivity alarm. This guide explains what the coolant does, why water quality matters so much, what to avoid, and how to keep the loop clean between services. Table of Contents What Laser Chiller Coolant Actually Does Why Water Quality Matters Distilled, Deionized, or Tap Water? When Antifreeze and Additives Belong How Often to Change the Coolant Signs the Coolant Needs Attention Frequently Asked Questions What Laser Chiller Coolant Actually Does Reger Laser sells and services Orion industrial water chillers and supports the laser cutting machines they cool, so we see the inside of a lot of cooling loops. The job of the coolant is to carry heat away from the parts of the laser that make it: the source or resonator, the cutting head, and the beam delivery optics. The chiller removes that heat and sends the coolant back at a controlled temperature. Many fiber lasers run two circuits at different temperatures, one for the source and one for the head and optics. Both circuits depend on clean coolant flowing freely. If flow drops or the coolant carries contamination, the source and optics run hotter than they were designed to, and that shortens their life even when no alarm goes off. Why Water Quality Matters Three things go wrong in a cooling loop, and all three start with what is in the water. Scale Tap water carries dissolved minerals, mostly calcium and magnesium. The U.S. Geological Survey’s page on water hardness explains how those minerals leave deposits when water is heated. In a laser, those deposits coat heat exchanger surfaces and narrow the small channels in the cutting head and source, which cuts heat transfer and flow. Conductivity and corrosion Dissolved minerals also make water conduct electricity. USGS covers the basics in its page on conductivity and water. Many lasers monitor coolant conductivity because high conductivity speeds up corrosion in mixed-metal loops and can be a problem around electrical components. That is why some machines use a deionizing filter in the loop and alarm when conductivity climbs. Biological growth Warm water, light, and time grow algae and bacteria. The slime they form clogs filters and strainers, coats heat exchanger surfaces, and can foul small passages. Clear tubing and reservoirs that sit in light make it worse. Distilled, Deionized, or Tap Water? Follow the manual first. Beyond that, here is how the common options compare in general. Distilled water has most of the minerals removed, so it does not scale the way tap water does. Many manufacturers specify it. Deionized water has dissolved ions removed and very low conductivity. Very pure water can be aggressive toward some metals over time, which is why manufacturers that specify it often pair it with an approved inhibitor or a deionizing filter that holds conductivity in a set range. Tap water varies from town to town and even season to season. It brings minerals, chlorine, and whatever else is in the local supply. Keep it out of the loop, including for top-offs. The most common mistake we see is not the initial fill. It is the top-off. A loop filled correctly and then topped off with tap water for a year ends up with most of the problems tap water brings. Keep a supply of the right water next to the chiller so nobody is tempted. When Antifreeze and Additives Belong Antifreeze is the additive people ask about most. Glycol protects against freezing, which matters if the chiller or lines sit where temperatures drop below freezing, or if the machine will be moved or stored in the cold. But glycol also changes how well the coolant carries heat, and not every laser allows it. Some manufacturers approve a specific product at a specific concentration. Others do not allow it at all. The same rule applies to corrosion inhibitors and biocides. Use only what the manufacturer approves, at the ratio it specifies, and never mix products from different suppliers. Additives that are fine on their own can react with each other or with seals and hoses in ways that are hard to undo. If your shop has winterized a chiller in the past, or you are not sure what is in the loop right now, drain, flush, and refill with a known coolant rather than guess. How Often to Change Laser Chiller Coolant The manual gives the interval, and it is usually based on run time or calendar time, whichever comes first. Treat it as a maximum, not a target. Shops in dusty environments, shops that run multiple shifts, and shops where the chiller sits in a warm or bright spot often need to change coolant sooner. A full change should include flushing the loop, not just draining and refilling, along with replacing filters and checking the deionizing cartridge if the system has one. Our laser chiller maintenance guide covers the full procedure, and we handle chiller flushing as part of our preventive maintenance visits. Signs the Coolant Needs Attention The coolant looks cloudy, colored, or has particles in it. There is visible growth in the reservoir, sight glass, or clear tubing. Conductivity alarms appear or the deionizing cartridge is exhausting faster than it used to. Filters and strainers clog between scheduled changes. Flow or pressure readings are drifting,

Robotic arm working alongside industrial machinery, one form of automation shops add to a laser cutting cell
Buying & Ownership, Laser Cutting

Should a Small Shop Automate Its Laser Cutting? 6 Questions to Answer First

A small shop should automate laser cutting when the laser is sitting idle while people load sheets, pull parts, and sort skeletons, and when there is enough steady work to keep an automated cell busy. If the beam is off more than it is on during a shift because the operator is handling material, automation usually pays off in capacity. If the machine is already cutting most of the shift and the real bottleneck is bending, welding, or programming, automating the laser just moves parts faster to a pile that is already waiting. The decision is less about the technology and more about where time is actually lost in your shop. This guide walks through six questions that sort that out, the common types of laser automation, and what to plan for so an automated cell runs the way you expected it to. Table of Contents What It Means to Automate Laser Cutting Question 1: Where Is the Time Going? Question 2: Is There Enough Steady Work? Question 3: How Do You Schedule? Question 4: Do You Have the Space? Question 5: Who Will Run and Maintain It? Question 6: Is the Laser Itself Ready? Frequently Asked Questions What It Means to Automate Laser Cutting Reger Laser sells and supports laser cutting machines and the automation around them, and when shops ask us about automation they usually mean one of a few things. Most cells combine several of these. Load and unload systems that move raw sheets onto the shuttle table and pull cut sheets off. Material storage towers that hold multiple materials and thicknesses and feed the laser from a queue. Part sorting that picks finished parts out of the skeleton and stacks them, like our PMG parts picker. Software for nesting, scheduling, and tracking jobs through the cell. The right mix depends on the answers to the questions below. Our laser cutting automation page covers the systems we offer. Question 1: Where Is the Time Going? Start by measuring, not guessing. For a week or two, track how much of each shift the laser is actually cutting and how much it is waiting. Most controls log beam-on time or cycle time, and a simple sheet at the machine can capture the rest: waiting for material, loading, unloading, sorting parts, clearing a jam, changing nozzles. If loading, unloading, and sorting eat a large share of the shift, automation targets exactly that time. If the laser is mostly cutting and parts pile up downstream, your money is better spent downstream. Our post on fiber laser downtime covers how to find and fix the other sources of lost time, because some of them can be solved without any automation at all. Question 2: Is There Enough Steady Work? Automation earns its keep on volume. A cell that sits idle half the week because the work is not there is an expensive way to store sheet metal. Look at your backlog and your quoting pipeline, not just a busy month. Shops with steady repeat work, recurring customers, or their own product lines tend to get the most from it. Job size matters too. Automation handles long runs of the same material effortlessly. It also handles high-mix work well if the software and storage are set up for it, but that setup takes more planning. A useful exercise is to look back over the last year and ask how many weeks the laser would have been fully loaded with an automated cell in place. If the answer is most of them, the case for automation is strong. If the work comes in bursts with long quiet stretches between, it may make more sense to add a shift or improve nesting and scheduling first, and revisit automation once the workload is steadier. The goal is a cell that stays busy, not one that looks impressive on the floor. Question 3: How Do You Schedule? One of the biggest gains from automation is the ability to keep cutting when nobody is standing at the machine: through breaks, shift changes, and in some shops, unattended overnight. That only works if the shop plans for it. Somebody has to program and nest enough work to fill those hours, stage the material, and trust the machine to run. Nesting quality gets more important when the cell is feeding itself. Our laser cutting nesting post covers how to get more parts out of every sheet, which matters twice as much when those sheets are coming out of a tower without a person checking them. Question 4: Do You Have the Space? Automation takes floor space, and not just for the equipment itself. You need room for forklifts or cranes to load raw material, room for finished parts and skeletons to leave the cell, and room for technicians to reach every side for service. Some storage systems also need ceiling height. Sketch the whole material flow, from the dock to the next operation, before choosing a system. A cell that fits on paper but blocks the path to the press brakes creates a new bottleneck. Question 5: Who Will Run and Maintain It? Automation changes jobs rather than removing them. Someone still programs the work, stages material, handles exceptions, and keeps the equipment maintained. Suction cups, sensors, and grippers are wear items, and an automated cell adds moving parts that need a place on the maintenance schedule. Guarding also changes, because moving loaders and pickers create new hazards around the machine. OSHA’s machine guarding guidance applies to the whole cell, not just the laser. If your team is stretched, plan for training before the equipment arrives. Small manufacturers can also get outside help planning the change. The NIST Manufacturing Extension Partnership has centers in every state that work with small and mid-sized shops on process and productivity improvements. Question 6: Is the Laser Itself Ready? Automation multiplies whatever the laser already does. A machine with inconsistent cut quality, frequent pierce failures, or tip-ups will produce those problems faster and

Machine operator wearing safety glasses while running equipment, the person who owns the laser shift start checklist
Maintenance & Service, Training & Safety

What Should a Laser Operator Check at the Start of Every Shift?

A good laser cutter daily checklist covers five areas before the first program runs: safety systems, the cutting head and optics, assist gas, cooling, and the table and motion system. Once an operator has done it a handful of times it becomes a short routine, and it catches most of the problems that otherwise show up halfway through a nest as dross, a burned protective window, a pierce that will not go through, or a head collision. The shops we see with the fewest emergency calls are not the ones with the newest machines. They are the ones where every operator checks the same things in the same order at the start of every shift. The checklist below is a starting point built from the service calls we get most often. Adjust it to your machine’s manual, post it at the control, and make it part of how every new operator is trained. Table of Contents Why a Laser Cutter Daily Checklist Matters Safety Systems Cutting Head and Optics Assist Gas Chiller and Cooling Tables, Slats, and Motion End of Shift Making the Checklist Stick Frequently Asked Questions Why a Laser Cutter Daily Checklist Matters Reger Laser services and supports fiber and CO2 cutting machines for fabrication shops across the country, and a lot of the repairs we do trace back to something that was visible at the start of the shift. A window with a spatter mark. A nozzle with a nick. A chiller running a few degrees warm. Gas pressure a little low because a bottle was near empty. Each of those is a two-minute fix before the first cut and a much bigger problem after a few hours of production. A daily checklist also makes a shop less dependent on one experienced operator. When the routine is written down, the second shift and the new hire check the same things the veteran does. That consistency is the whole point of the operator training we provide, and it is the foundation of any preventative maintenance program. Safety Systems Start with the things that protect people, because a machine that cuts perfectly with a bypassed interlock is not a machine anyone should run. Walk the machine and confirm guards, enclosure panels, and viewing windows are in place and undamaged. Test the emergency stops and confirm door and light curtain interlocks stop the machine. Confirm the fume extraction or dust collector is running and not alarming. Clear the area around the machine of scrap, tools, and anything that could trip someone or catch fire. Confirm a fire extinguisher is in its place and charged. OSHA’s guidance on machine guarding and its laser hazards overview are good references for why these checks matter. The laser beam in most cutting machines is infrared and invisible, so the enclosure and interlocks are what keep it where it belongs. Cutting Head and Optics The cutting head is where most daily problems start, and it is the area most worth a careful look. Protective window. Inspect it under good light for haze, pits, or burn marks, and replace it if you see any. Our guide to the laser protective window covers what to look for. Nozzle. Check the orifice for spatter, nicks, and roundness, and confirm it is seated tight. See our laser cutting nozzle guide for how damage shows up in the cut. Beam centering. Run a centering check if the machine or the nozzle has been changed or bumped. Height sensing. Calibrate the capacitive height sensor after a nozzle change, and confirm it responds. Focus. Confirm focus settings match the material in the first program. Assist Gas Assist gas problems look like cutting problems, so they are easy to misdiagnose. Checking supply before the first cut saves a lot of confusion later. Confirm there is enough oxygen, nitrogen, or air on hand for the shift’s jobs. Check that supply pressure at the regulator matches what the machine needs. Listen for leaks at fittings and hoses, and look for damaged lines. If the shop uses compressed air as an assist gas, drain the separators and confirm the dryer is working, because oil and water in the air end up on the optics. Our assist gas guide explains how each gas affects the cut and what purity and pressure problems look like on the part. Chiller and Cooling Confirm the chiller is running and holding its set temperature before the source is turned on. Check the coolant level and look for leaks under the chiller and along the lines. Confirm the condenser and filters are not clogged with dust. Note any chiller alarms, even ones that cleared on their own. A chiller that runs warm will not always stop the machine right away, but it shortens the life of the source and the optics. If the chiller is struggling, our post on why a laser chiller overheats walks through the usual causes. Tables, Slats, and Motion Look at the slats. Heavy slag buildup lifts sheets, causes tip-ups, and leads to collisions. Confirm the shuttle tables move freely and nothing is caught in the exchange path. Clear scrap from the bed and the conveyor or scrap bins. Home the machine and listen for new noises from the axes as it moves. Check the drive rails for debris that could reach bearings and racks. End of Shift The last five minutes of a shift set up the next one. Clean the head area, empty scrap bins, note anything unusual in a machine log, and report problems instead of leaving them for the next operator to discover. A shared log turns a vague complaint like “it has been cutting funny” into something a technician can actually diagnose. A good end-of-shift log does not need to be elaborate. Record the date, the operator, the materials cut, any alarms, any consumables changed, and anything that sounded, looked, or cut differently than usual. Over a few months that log becomes one of the most useful tools a technician has, because

Scroll to Top
0

No products in the cart.

No products in the cart.